Home  > Fleece Performance(x)
View:
High quality stainless steel f

Features:

  • 1/2" Barbed Inlet
  • Made from 316 Stainless Steel
  • Includes sealing washer
Item#:
244-FPE-CP3-FEED
Manufacturer Item:
FPE-CP3-FEED
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here
Fleece Performance Cheetah Tur

The Cheetah series does not require an expensive kit, just bolt it on and go. Designed as a stock appearing, drop in replacement turbo capable of much more!. With our exclusive FMW compressor wheel and inconel turbine wheel technology, you’ll enjoy smooth throttle response and big top-end power. For optimal performance, our HX35 is recommended for use with additional fueling upgrades. 

Cheetah Turbocharger Benefits:

  • Fleece Performance Exclusive FMW Compressor Wheel Technology.
  • Capable of supporting vehicle modifications up to 650 RWHP
Item#:
244-FPE-HX35-63-FMW
Manufacturer Item:
FPE-HX35-63-FMW
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here
Original LB7 Injection lines will corrode and break and are a leading cause of contamination when changing the injectors. If you are changing your injectors, have a line failure, or are looking to upgrade your stock lines, we’ve got you covered with our all new Fleece Performance LB7 Injection Lines!

 
Features:
  • Complete set of 8 new lines
  • Machined 4140 injector swivel nuts
  • Corrosion resistant lines

 

Includes:

  • (Qty 2) Line for Cylinders 1 and 8 - Replaces GM Part# 97188720
  • (Qty 2) Line for Cylinders 2 and 7 - Replaces GM Part# 97188723
  • (Qty 2) Line for Cylinders 3 and 6 - Replaces GM Part# 97188721
  • (Qty 2) Line for Cylinders 4 and 5 - Replaces GM Part# 97188722
Item#:
244-FPE-34611
Manufacturer Item:
FPE-34611
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

Kit Contents:

  • Dash 6 Oil Feed Line
  • 90 Degree Oil Feed Fitting
  • Engine Block Oil Feed Fitting
  • Turbo Drain Flange Upper
  • Turbo Drain Flange Lower
  • Turbo Drain Flex Extension
  • (2) 3/8 Turbo Drain Bolts
  • (2) Turbo Drain Extension Clamps
  • Stock Oil Feed Galley Plug
  • Turbo Pedestal Studs and Nuts (Short and Long Kit)
  • Turbo T4 Pedestal Gasket
  • Turbo Thermostat Delete Plug
  • Turbo Coolant Return Plug and Clamps
Item#:
244-TURBOINSTKITDMAX
Manufacturer Item:
TURBO-INST-KIT-DMAX
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

Our S300-S400 Duramax Turbo Drain Tube Kit is designed to take the headache out of installing/removing the factory drain tube that is difficult to get to and tends to get damaged during the install/removal process. Simply bolt the turbo drain nipple to the turbo, install the lower turbo drain tube and the silicone hose, and install the turbo into location while inserting the nipple into the hose. This is great for competitors that remove and install their turbo multiple times.

Turbo Drain Tube Kit Includes:

  • FPE-34131 - Universal Turbo Drain Nipple (7/8" Hose)
  • FPE-34132 - 2001-2010 Duramax Lower Turbo Drain Tube (LB7, LLY, LBZ, LMM)
  • 8" of 0.870" 4 Ply Silicone Hose
  • (2) Hose Clamps 
  • Gaskets
Item#:
244-FPE-DTDT-0110
Manufacturer Item:
FPE-DTDT-0110
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here
Amplify your driving experienc

The Cheetah series does not require an expensive kit, just bolt it on and go. Designed as a stock appearing, drop in replacement turbocharger capable of much more! With our exclusive FMW compressor wheel and inconel turbine wheel technology, you’ll enjoy smooth throttle response, big top-end power, and that classic Cheetah Turbocharger sound. 

Cheetah Turbocharger Benefits:

  • Fleece Performance Exclusive FMW Compressor Wheel Technology.
  • Capable of supporting vehicle modifications up to 650 RWHP

 

To confirm proper fitment for your truck verify that the tenth digit of your VIN is a 3 or 4.  If the tenth digit is a 5 or higher, you need to purchase FPE-351-0407.

Item#:
244-FPE-351-0304
Manufacturer Item:
FPE-351-0304
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

If you have an aftermarket fuel filtration system such as an Air Dog® or a FASS® and dual CP3 pumps, this fuel distribution block will allow you to get rid of your unnecessary factory fuel filter and give you a convenient and clean location to route your feeds, returns, and sensors. It mounts in the factory fuel filter location to allow you to use your factory return lines without any relocating or bending. It also features a port for the factory WIF (water in fuel) sensor, a 9/16-18 o-ring port (dual CP3 return port), (3) 3/4-16 o-ring ports (feed ports), and (2) 1/8” NPT ports (sensor ports).

Kit Includes:

  • Fuel Block
  • Replacement Banjo Washers
  • WIF Sensor Port
  • 9/16-18 o-ring to -6AN male fitting (dual CP3 return port)
  • 9/16-18 o-ring port plug
  • (3) 3/4-16 o-ring to -8AN male fittings (feed ports)
  • 3/4-16 o-ring port plug
  • (2) 1/8” NPT ports (sensor ports)
Item#:
244-FPE-FFD-RF-3G
Manufacturer Item:
FPE-FFD-RF-3G
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

If you have an aftermarket fuel filtration system such as an Air Dog or a FASS, your factory fuel filter is no longer necessary. The factory fuel filter only becomes an extra restriction and an eye sore. This fuel filter delete will remove that restriction and help clean up under the hood of your truck. It mounts perfectly to allow the factory fuel return lines to be used without any relocating or bending. It also features a port for the factory WIF (water in fuel) sensor and a 9/16-18 O-ring port for a dual* CP3 return line.

Kit Includes:

  • Fuel Filter Delete Block
  • Replacement Banjo Washers
  • WIF Sensor Port Plug (M14x2.0)
  • 9/16-18 O-ring Port Plug

 

*Contact Fleece Performance for dual CP3 return fittings and line

Item#:
244-FPE-FFD-RO-3G
Manufacturer Item:
FPE-FFD-RO-3G
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

Features:

  • High Quality AN fittings
  • Extra Flexible Smooth Bore Tefllon Hose
Item#:
244-FPE-CRTFL-OE
Manufacturer Item:
FPE-CRTFL-OE
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

Features: 

  • High Quality AN fittings
  • Extra Flexible Smooth Bore Tefllon Hose
Item#:
244-FPE-CRTFL-S3S4
Manufacturer Item:
FPE-CRTFL-S3S4
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here

The kit includes everything you need to properly route, plumb and filter fuel for your Cummins engine from a Fleece Performance lift pump to the injection pump.  Our kit improves accessibility to the fuel filter as well as reduces your ongoing maintenance cost with a lower cost Donaldson filter.

Fleece Performance fuel filter delete is required for use with this product and must already be installed or purchased separately. This kit does not include a quick disconnect fitting to adapt to the OE lift pump. If you are running this to a stock OE sending unit on the fuel tank use P/N: FPE-QUCON-OE-38 to allow for an AN connection to the stock quick disconnect style fitting.  

Kit includes: 

  • Donaldson 3 micron fuel filter and water separator
  • Filter base with integral mounting
  • Distribution filter block / filter coupler
  • Push Lock hose and all necessary AN and barb fittings
  • CP3 Feed fittings for 5.9L and 6.7L

  

Visit our Resources page for installation instructions. 

Item#:
244-FPE-34783
Manufacturer Item:
FPE-34783
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here
Amplify your driving experienc

The Cheetah series does not require an expensive kit, just bolt it on and go. Designed as a stock appearing, drop in replacement turbocharger capable of much more! With our exclusive FMW compressor wheel and inconel turbine wheel technology, you’ll enjoy smooth throttle response, big top-end power, and that classic Cheetah Turbocharger sound.

Cheetah Turbocharger Benefits:

  • Fleece Performance Exclusive FMW Compressor Wheel Technology.
  • Capable of supporting vehicle modifications up to 650 RWHP

 

NOTE: For MY2004.5 trucks, you must verify proper fitment using the VIN. To do this, verify that the tenth digit of your VIN is a 5 or higher.  If the tenth digit is a 4, you need to purchase FPE-351-0304.

Item#:
244-FPE-351-0407
Manufacturer Item:
FPE-351-0407
Manufacturer:
Fleece Performance
You must be logged in to order this item. Log in here
View: