Home  > Painless Wiring(x)
View:
23 Circuit Harness - Pro-Series - GM Keyed Column - Grommet
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a grommet style firewall pass through with the fuse block mounted inside the vehicle on or near the firewall. The wires are pre-terminated using Packard factory crimping machines and utilize a grommet to pass through the firewall, keeping your wiring safe and protected from harsh metal edges. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with a pre-terminated GM Column Mounted Ignition switch connector, allowing you to simply plug into GM keyed and many aftermarket columns that utilize the GM keyed ignition switch! Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Front Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factory GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips.
Item#:
419-10401
Manufacturer Item:
10401
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
23 Circuit Harness - Pro-Series - Key In Dash - Grommet
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a grommet style firewall pass through with the fuse block mounted inside the vehicle on or near the firewall. The wires are pre-terminated using Packard factory crimping machines and utilize a grommet to pass through the firewall, keeping your wiring safe and protected from harsh metal edges. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with adaptable open-ended ignition switch wiring and terminals, allowing you to adapt to any ignition switch you desire! GM old style (3-3/4) and new style (4-1/4) turn signal switch connectors are included. Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factory GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips.
Item#:
419-10402
Manufacturer Item:
10402
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
23 Circuit Harness - Pro-Series - GM Keyed Column - Bulkhead
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a GM Bulkhead style firewall pass through with the fuse block mounted inside the vehicle on the firewall, the exact same connector GM used on many vehicles from 1968-up. The wires are pre-terminated using Packard factory crimping machines and utilize a bulkhead to mount to and pass through the firewall, keeping your wiring safe and protected and allowing you to easily disconnect the firewall forward wiring without having to remove wiring from each individual component. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with a pre-terminated GM Column Mounted Ignition switch connector, allowing you to simply plug into GM keyed and many aftermarket columns that utilize the GM keyed ignition switch! Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factory GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector GM brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10403
Manufacturer Item:
10403
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
23 Circuit Harness - Pro-Series - Key In Dash - Bulkhead
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a GM Bulkhead style firewall pass through with the fuse block mounted inside the vehicle on the firewall, the exact same connector GM used on many vehicles from 1968-up. The wires are pre-terminated using Packard factory crimping machines and utilize a bulkhead to mount to and pass through the firewall, keeping your wiring safe and protected and allowing you to easily disconnect the firewall forward wiring without having to remove wiring from each individual component. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with adaptable open-ended ignition switch wiring and terminals, allowing you to adapt to any ignition switch you desire! GM old style (3-3/4) and new style (4-1/4) turn signal switch connectors are included. Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factor GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10404
Manufacturer Item:
10404
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
23 Circuit Harness - Pro-Series - Truck - GM Keyed Column - Bulkhead
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a GM Bulkhead style firewall pass through with the fuse block mounted inside the vehicle on the firewall, the exact same connector GM used on many vehicles from 1968-up. The wires are pre-terminated using Packard factory crimping machines and utilize a bulkhead to mount to and pass through the firewall, keeping your wiring safe and protected and allowing you to easily disconnect the firewall forward wiring without having to remove wiring from each individual component. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with a pre-terminated GM Column Mounted Ignition switch connector, allowing you to simply plug into GM keyed and many aftermarket columns that utilize the GM keyed ignition switch! Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factor GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10405
Manufacturer Item:
10405
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
25 Circuit Harness - Pro-Series - GM Keyed Column - Grommet
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a grommet style firewall pass through with the fuse block mounted inside the vehicle on or near the firewall. The wires are pre-terminated using Packard factory crimping machines and utilize a grommet to pass through the firewall, keeping your wiring safe and protected from harsh metal edges. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with a pre-terminated GM Column Mounted Ignition switch connector, allowing you to simply plug into GM keyed and many aftermarket columns that utilize the GM keyed ignition switch! Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factor GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10411
Manufacturer Item:
10411
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
25 Circuit Harness - Pro-Series - Key In Dash - Grommet
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a grommet style firewall pass through with the fuse block mounted inside the vehicle on or near the firewall. The wires are pre-terminated using Packard factory crimping machines and utilize a grommet to pass through the firewall, keeping your wiring safe and protected from harsh metal edges. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with adaptable open-ended ignition switch wiring and terminals, allowing you to adapt to any ignition switch you desire! GM old style (3-3/4) and new style (4-1/4) turn signal switch connectors are included. Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factor GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10412
Manufacturer Item:
10412
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
25 Circuit Harness - Pro-Series - Truck - GM Keyed Column - Bulkhead
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a GM Bulkhead style firewall pass through with the fuse block mounted inside the vehicle on the firewall, the exact same connector GM used on many vehicles from 1968-up. The wires are pre-terminated using Packard factory crimping machines and utilize a bulkhead to mount to and pass through the firewall, keeping your wiring safe and protected and allowing you to easily disconnect the firewall forward wiring without having to remove wiring from each individual component. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with a pre-terminated GM Column Mounted Ignition switch connector, allowing you to simply plug into GM keyed and many aftermarket columns that utilize the GM keyed ignition switch! Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factory GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10415
Manufacturer Item:
10415
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
25 Circuit Harness - Pro-Series - Truck - Key In Dash - Bulkhead
The Painless Pro Series gives you everything you need to wire up your pro-touring or custom ride right the first time! Ample length is provided for each circuit, providing you the freedom to route and hide your wiring how you choose. Once youve got the harness fit how you like it, included are over 25 GM factory style connectors found on most 60s to early 90s GM switches, allowing you to turn the Pro Series harness into a direct fit harness for your application. LED ATC bladed fuses get you away from the old hard-to-find glass fuses, and will light up if blown making troubleshooting a painless task. The 6 gauge charge wire and midi fuse (no more problematic fusible link!) will keep up with todays high amperage alternators, and the provided front and rear ground harnesses making grounding your lighting circuits a breeze! Provided with many GM connectors and terminal, insulated and non-insulated butt splices, heat shrink, grommets, cable ties, ground straps, and cable tie clips, the Pro Series brings a new meaning to truly Painless wiring and includes our lifetime guarantee. This harness features a GM Bulkhead style firewall pass through with the fuse block mounted inside the vehicle on the firewall, the exact same connector GM used on many vehicles from 1968-up. The wires are pre-terminated using Packard factory crimping machines and utilize a bulkhead to mount to and pass through the firewall, keeping your wiring safe and protected and allowing you to easily disconnect the firewall forward wiring without having to remove wiring from each individual component. Each wire is extra length with up to 20 of length to the front and over 25 to the rear providing ample length for mounting your fuse block and freedom to route the wiring how you choose. After trimming to fit, utilize the provided terminals & connectors to terminate the ends. This harness comes with adaptable open-ended ignition switch wiring and terminals, allowing you to adapt to any ignition switch you desire! GM old style (3-3/4) and new style (4-1/4) turn signal switch connectors are included. Included with the GM Pro Series harnesses is: (4) H4 Headlight connectors- to support single (high/low) or dual headlights (separate high beams) (2) Turn signal connectors- fits connectors found on factory GM hard wired turn signals (4) Molded ¼ sockets for front & rear marker lights (2) HEI distributor connectors (+ and Tach) (2) Connectors for factor GM wiper motor GM washer pump connector Courtesy light sockets GM headlight switch connector GM dimmer switch connector Gm brake switch connector GM turn signal switch flat connectors (early & late) GM ignition switch connectors* Neutral Safety Switch connector (column mounted or factory floor shifter mounted) Reverse Switch connector (column mounted or factory floor shifter mounted) Braided ground straps (for body and core support to frame grounding, also includes (6) self-tapping ¼ screws for mounting) Alternator bag kit with terminals, splices, resistor, diode to connect the alternator. (1) Connector for GM 10si alternator Assortment of insulated and non-insulated splices, ring terminals, heat shrink, grommets, cable ties, and cable tie clips. * Only on GM keyed column harnesses
Item#:
419-10416
Manufacturer Item:
10416
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
GM Pickup Socket Pigtail Kit (Single Round Headlights) (73-80)
these socket kits give you all the terminals and connectors you need to wire you exterior lighting on your 1973-1980 single round headlight GM Pickup.
Item#:
419-30350
Manufacturer Item:
30350
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
GM Pickup Socket Pigtail Kit (Single Square Headlights) (80-87)
these socket kits give you all the terminals and connectors you need to wire you exterior lighting on your 1980-1987 single square headlight GM Pickup.
Item#:
419-30351
Manufacturer Item:
30351
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
GMC Suburban Socket Pigtail Kit (Dual Square Headlights) (88-91)
these socket kits give you all the terminals and connectors you need to wire you exterior lighting on your 1988-1991 Dual Square Suburban front end.
Item#:
419-30353
Manufacturer Item:
30353
Manufacturer:
Painless Wiring
You must be logged in to order this item. Log in here
View: