Home  > Design Engineering(x)
View:
2" x 50ft Exhaust Wrap - Tan
Wrapping headers and down pipes is an important first step in reducing unwanted and power-robbing under hood heat. Less under hood heat results in a cooler air charge for improved performance and keeping exhaust gases hotter within the exhaust system helps in decreasing exhaust density & increases exhaust flow.
Item#:
147-010102
Manufacturer Item:
010102
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Stainless Steel Locking Ties 8" (8 per pack)
Locking Ties are perfect for securing wrap to pipes with it's self-locking design. Locking Ties offer many other uses including bundling wires, hoses, and other forms of insulation products. Just slide end into locking mechanism and pull tight.
Item#:
147-010201
Manufacturer Item:
010201
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Stainless Steel Locking Ties 14" (4 per pack)
Locking Ties are perfect for securing wrap to pipes with it's self-locking design. Locking Ties offer many other uses including bundling wires, hoses, and other forms of insulation products. Just slide end into locking mechanism and pull tight.
Item#:
147-010202
Manufacturer Item:
010202
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Black HT Silicone Coating (6 per master carton)
The High Temperature (HT) Silicone Coating provides lasting protection for any hot surface up to 1500 degrees. DEI recommend the use of this coating with their exhaust wrap because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home. HT Silicone Coating is VOC (Volatile Organic Compounds) compliant in all 50 states.
Item#:
147-010301
Manufacturer Item:
010301
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
White HT Silicone Coating (6 per master carton)
The High Temperature (HT) Silicone Coating provides lasting protection for any hot surface up to 1500 degrees. DEI recommend the use of this coating with their exhaust wrap because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home. HT Silicone Coating is VOC (Volatile Organic Compounds) compliant in all 50 states.
Item#:
147-010303
Manufacturer Item:
010303
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Motorcycle Exhaust Wrap Kit (Black wrap w/Black HT Silicone Coating)
A simple and effective way to control heat, protect against serious leg burns and improve performance. Pipe wrap kits contain everything needed to wrap a set of pipes all in one convenient package.
Item#:
147-010330
Manufacturer Item:
010330
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Versa-Shield Starter Shield 5-1/4" w x 16-1/2" l - Universal (Mini) Heat Sh
Versa-Shield was designed to protect starters from potential failure caused by under hood heat soak conditions. Constructed using an aluminized heat reflective material backed with a hi-temp rated glass fiber insulation barrier, Versa-Shield is capable of reflecting radiant heat up to 2000°F.
Item#:
147-010384
Manufacturer Item:
010384
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Aluminum Plug Wire Sheath 3/4" x 6" (4-pack)
Aluminized Plug Wire Sheaths are constructed from high-temperature rated glass fiber material bonded to a heat reflective aluminized material. Plug Wire Sheaths are an inexpensive alternative for protecting specific areas on both ignition wire and boot locations from damaging heat generating sources..
Item#:
147-010409
Manufacturer Item:
010409
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Reflect-A-Cool 36" x 48" sheet (Bulk yardage available)
Reflect-A-Cool, constructed of fiberglass material backed with a layer of aluminized reflective foil to handle direct continuous temperature of 400°F has many uses such as covering firewalls, marine engine compartments, RVs, in the tub of a racecar where typical mechanical fasteners cannot be used and has many industrial uses.
Item#:
147-010412
Manufacturer Item:
010412
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Cool-Tape Plus 2" x 60ft roll
Cool Tape is a flexible and super strong self-adhesive thermal insulating tape capable of protecting up to 2000°F of radiant heat. Made of one mil aluminized material bonded to a woven glass fiber heat resistant matting, Cool Tape is a ultra light weight heat reflective solution for wrapping wires, cables, hoses, fuel lines, covering seams and many other uses.
Item#:
147-010413
Manufacturer Item:
010413
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Reflect-A-Cool 24" x 24" sheet
Reflect-A-Cool, constructed of fiberglass material backed with a layer of aluminized reflective foil to handle direct continuous temperature of 400°F has many uses such as covering firewalls, marine engine compartments, RVs, in the tub of a racecar where typical mechanical fasteners cannot be used and has many industrial uses.
Item#:
147-010462
Manufacturer Item:
010462
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
Fire Sleeve & Tape Kit - 1" I.D. x 36"
Constructed from a high temperature resistant braided glass material, woven into a sleeve and heavily coated with 100% iron oxide silicone rubber, Fire Sleeve provides the ultimate in heat insulation and protection from direct heat up to 500°F.
Item#:
147-010474
Manufacturer Item:
010474
Manufacturer:
Design Engineering
You must be logged in to order this item. Log in here
View: